In heat treating of tin-rich alloys, it is difficult to secure an effective and
permanent degree of hardening. Tin melts at 232°C (505 K), and therefore room
temperature (about 295 K) is well over one-half the absolute melting point. It follows
that high-temperature behavior such as recrystallization and recovery can occur in
fairly short times, even at room temperature. Tin is also an unusual metal because
it can work soften under certain conditions, and so heat treating can be used in
these cases to restore some of the original hardness and strength.
Heat treating of tin-rich alloys has been practiced for bearing alloys, pewter ware
and organ pipe alloys. Some of the principles underlying these applications will be
reviewed first.
Binary Alloys
Tin-antimony, tin-bismuth, tin-lead, and tin-silver alloys can all be temper
hardened by solution treatment and aging. However, only the tin-antimony alloys can
be permanently strengthened by heat treatment; all other tin-rich binary alloys will
gradually soften at room temperature.
The greatest improvement obtainable in binary tin-antimony alloys occurs in the
alloy that contains 9% Sb; a hardness of 21 HB and a tensile strength
of 51 MPa (7.4 ksi) can be increased to 26 HB and 65 MPa (9.4 ksi). This alloy is
tempered for 48 h at 100°C (212°F) after being quenched from 225°C
(435°F). During this tempering treatment, ductility decreases from 20 to 10%
elongation.
Ternary Alloys
Permanent effects produced by heat treatment also carry over into ternary alloys
of tin, antimony, and cadmium. This was discovered during an early investigation of
the strength and hardness of ternary alloys containing up to 43% Cd
and 14% Sb using chill-cast specimens.
It was found that the strengthening effect of cadmium in the terminal solution tin
phase (alpha) is much greater than that of antimony. In this study, the maximum stable
values obtained in alloys containing 7 to 9% Sb and 5 to 7%
Cd were as follows: tensile strength 108 MPa (15.7 ksi), elongation
15%, and hardness 35 HB. The presence of the sigma phase (principally SbSn) as
primary cuboids had no effect on strength or hardness, but the presence of primary
epsilon (CdSb) destroyed the useful mechanical properties.
Therefore, alloys containing cadmium generally use compositions that restrict the
formation of the primary (CdSb) epsilon phase. The maximum combination of strength,
ductility, and hardness is obtained in alloys that have finely dispersed precipitates
of the sigma and epsilon phases in an alpha matrix, or finely dispersed epsilon in a
matrix of alpha with a eutectoid of (α + γ). These structures are typically achieved
by quenching or rapid cooling from elevated temperatures to avoid precipitation of
primary sigma and epsilon.
Additional heat-treatment studies have been directed to a group of cold-workable
tin-rich alloys containing 3 to 8% Cd and 1 to 9% Sb.
Two forms of hardening were observed on quenching of these alloys from 185 to
200°C (365 to 390°F). One form results from the change in solubility of
antimony in tin or in the beta phase. The other, which produces more intensive
hardening, is analogous to hardening of binary cadmium-tin alloys by quenching and
depends on suppression of eutectoid decomposition of the beta phase. Permanent
improvement results in the first instance. Therefore, a maximum tensile strength of
101 MPa (14.6 ksi) was achieved in a Sn-3Cd-7Sb alloy that was quenched from
190°C (375°F) and then aged for either 24 h at 100°C or 18 months at room
temperature.
Further studies have been carried out on tin-base alloys containing 7 to 10%
Sb and 0 to 3% Cd in an effort to locate a bearing
alloy that would be suitable at mildly elevated temperatures. In this composition
range, it was found that alloys containing 0.5 to 2% Cd (but not 3%)
can be strengthened considerably by quenching and tempering.
Optimum properties (tensile strength 92 Mpa) were obtained in a Sn-9Sb-1.5Cd alloy
quenched from 220°C (430°F) and then aged for 1000 h at 140°C. This alloy
consists of finely divided sigma and epsilon phases in a matrix of alpha.
Pewter
Many pewter articles are manufactured from sheet prepared by cold reduction of cast
bars or slabs. Tin-rich pewter alloys containing antimony and copper will work harden
during sheet-rolling operations that involve small percentage reductions (20%). If
left standing at room temperature, the alloy will recrysiallize and soften until it
has reverted to the hardness of the original cast bar or slab. On the other hand, if
large reductions (such as 90%) are made and the crystals are heavily worked, the
alloy will work soften. Then, as crystals increase in size, hardness increases slightly,
but never to the level of the original cast material.
The hardness values of spun pewter ware, or of other articles that have been
manufactured by mechanically working the metal, can be restored by heat treatment at
temperatures from 110 to 150°C. A tin alloy containing 6% Sb and
2% Cu hardens to 90% of the hardness of the as-cast material after
annealing for 1 h at 200 °C. Longer annealing times at lower temperatures have
smaller but similar effects on the recovery from work softening.
List of Articles - Knowledge Base